Allowables Evaluation for the Design of a Thermoplastic Fuselage

Revision as of 14:15, 29 April 2022

K. Muñoz^a, M. Jiménez^a, M. J. Mesa^a, R. Cabrera^a, S. Anaya^b, R. Elices^b, K. Fernández^c, M. I. Martín^c, J. Cuenca^c

^aElement Seville

^bAernnova

^c FIDAMC, Fundación para la Investigación, Desarrollo y Aplicación de Materiales Compuestos

Evaluación de Admisibles para el Diseño de un Fuselaje de Material Compuesto Termoplástico

Historia del artículo: Recibido 15 de abril 2022	Los polímeros reforzados con fibra de carbono se usan habitualmente en las estructuras primarias y secundarias de las aeronaves, debido principalmente a sus excelentes propiedades mecánicas específicas. Actualmente existe un interés creciente en el empleo de materiales compuestos de fibra de carbono y resina termoplástica en aplicaciones aeronáuticas, ya que estos ofrecen múltiples ventajas en comparación con los equivalentes termoestables. En este estudio se presentan los resultados de los ensayos mecánicos realizados a nivel de cupón y de elemento para la caracterización de las propiedades de un composite termoplástico que conformará un panel de fuselaje. Además de ensayos estandarizados, se llevan a cabo ensayos para evaluar el comportamiento de zonas críticas del panel, tales como el radio de las cuadernas, los larguerillos, y la unión entre cuaderna y piel alrededor de los larguerillos (mouse-hole). En el caso de estos últimos ensayos, se desarrollan procedimientos experimentales para su ejecución, incluyendo el diseño del utillaje necesario para reproducir las condiciones de contorno representativas. Como fruto de esta investigación, se han obtenido los admisibles para el diseño del panel curvo de fuselaje de material compuesto termoplástico. Este trabajo se desarrolla como parte del proyecto europeo DELTA, en el marco del programa de Clean Sky 2 JU. El objetivo de este proyecto es desarrollar y ejecutar procedimientos de ensayos experimentales innovadores que permitan validar paneles de fuselaje de material compuesto termoplástico, con el fin de aplicar estas soluciones en aviones de media y larga distancia (LPA). La culminación de este proyecto se alcanzará a través de la ejecución de un ensayo de panel curvo de fuselaje termoplástico bajo condiciones de carga representativas.
Palabras clave: Materiales compuestos Fuselaje termoplástico Caracterización mecánica

Allowables Evaluation for the Design of a Thermoplastic Fuselage

Keywords: Composites Thermoplastic fuselage Mechanical characterization	Carbon fibre reinforced polymers are commonly used in the primary and secondary structures of aircraft, mainly due to their excellent specific mechanical properties. Currently, there is a growing interest in the use of carbon fibre and thermoplastic resin composite materials in aeronautical applications, since they offer multiple advantages compared to thermosetting equivalents. This study presents the results of the mechanical tests carried out at the coupon and element levels for the characterization of the properties of a thermoplastic composite that will form a fuselage panel. In addition to standardized tests, tests are carried out to evaluate the behaviour of critical areas of the panel, such as the radius of the frames, the stringers, and the joint between the frame and the skin around the stringers (mouse-hole). In these latest tests, experimental procedures are developed for their execution, including the design of the necessary tools to reproduce the representative boundary conditions. As a result of this research, the allowables have been obtained for the design of the curved thermoplastic fuselage panel. This work is developed as part of the European project DELTA, within the framework of the Clean Sky 2 JU program. The objective of this project is to develop and execute innovative experimental test procedures that allow the validation of thermoplastic composite aircraft fuselage panels, in order to apply these solutions in medium and long-range aircraft (LPA). The ultimate goal of this project will be achieved through the execution of a curved thermoplastic fuselage panel test under representative load conditions.

1 Introduction

The use of carbon fibre reinforced polymers in primary and secondary aircraft structures has significantly risen in the latest few decades, mainly due to their excellent fatigue endurance and high specific strength when compared to ordinary metallic materials. [1] Thermoset resin based carbon fibre reinforced polymers (CFRP) have been the most matured technology for airframe manufacturing due to its excellent mechanical properties. Nevertheless, there is a growing interest in the use of thermoplastic resin based CFRP in aviation industry as developments in new resins and manufacturing technologies close the gap in performance compared to thermoset.

Thermoplastic polymers can be heat-softened, melted and reshaped as many times as desired. Additionally, they can be stored at room temperature and have an unlimited shelf life. This leads to a waste save and allows for more flexible manufacturing processes. Furthermore, their re-formability enable the correction of production tolerance errors and most importantly, re-usability and recyclability features of this nature of resins provides a great opportunity to reduce drastically the environmental impact of the global fleet.

The work presented here is framed in DELTA, [2] a European Research Project (Clean Sky 2 JU) lead by AERNNOVA which pursues the development and execution of innovative experimental test procedure that allow the validation of a thermoplastic composite fuselage panel, in order to apply these solutions in medium and long-range aircraft (LPA). One of the objectives of DELTA is to ensure the improved understanding of the structural response of a new concept for thermoplastic fuselage and proper design solutions for future application by means of experimental tests at two different structural complexity levels.

For that, a mechanical characterization at coupon and detail level of the thermoplastic matrix carbon fibre reinforced polymer is developed. As a result of this research, the allowables have been obtained for the design of the curved thermoplastic fuselage panel. With this information, DELTA will conclude with of the experimental validation of a curved thermoplastic panel test representative of a short & medium range aircraft fuselage.

2 Materials and Methods

2.1 Material and manufacturing process description

Figure 1 shows the final thermoplastic flat panel that was manufactured by FIDAMC, including the areas from where the specimens for Level 2 mechanical tests were extracted.

Figure 1. Thermoplastic flat panel manufactured by FIDAMC.

2.2 Mechanical tests

One of the objectives of this test campaign is to establish the fundamental material properties for subsequent use with structural analysis and design techniques. To this end, mechanical tests were carried out at the coupon and element levels for the characterization of the properties of the thermoplastic composite used in the fuselage panel manufacturing. In addition to standardized tests, tests were carried out to evaluate the behaviour of critical areas of the panel, such as the radius of the frames, the stringers, and the joint between the frame and the skin around the stringers (mouse-hole).

In the Table 1, the mechanical properties that were studied in this experimental test campaign are summarized. Number of specimens for each case is included. All of the tests were performed at RT conditions and no previous environmental conditioning was applied.

Table 1. Coupons & elements test campaign.

Test	Test Standard	Specimen dimensions (mm)	No. of specimens
FHT	ASTM D5766/ ASTM D6742	300 x 38.1	5
OHC	ASTM D6484 Proc. B	300 x 38.1	5
Bearing	ASTM D5961 Proc. B	342.9 x 38.1	3
Pull-through	ASTM D7332 Proc. B	108 x 108	6
Crippling	Experimental procedures	200 x 113	7
Unfolding		88 x 50	4
Debonding		88 x 25	3
Mouse hole		260 x 87	2

Once ELEMENT received the sections of the panel shown in the Figure 1, the specimens were extracted and prepared to perform the tests included in the Table 1. This preparation covered the installation of the stabilization tooling, installation of strain gages, drilling, etc. where applicable.

2.2.1 Filled-Hole Tension and Open-Hole Compression tests

The objective of these tests was to determine the properties of filled-hole tensile strength and open-hole compressive strength of the thermoplastic composite.

Filled-Hole Tension (FHT) tests were performed according to ASTM D5766/D5766M standard [3]. Provisions from ASTM D6742/D6742M [4] were also followed. Open-Hole Compression (OHC) tests were performed according to ASTM D6484/D6484M standard, following procedure B [5]. FHT and OHC tests were performed through a Universal Testing Machine Zwick Z250, equipped with a load cell up to 250 kN.

In the Figure 2, the set-up is shown for both tests. An edge-mounted average extensometer was used in these tests. In order to study specimens’ failure mode, the High-Speed Camera was used in FHT tests.


a	b

Figure 2. Set-up for (a) Filled-Hole Tension test; (b) Open-Hole Compression test.

2.2.2 Bearing Strength and Pull-through resistance tests

Bearing strength test aims to assess the bearing response of fastened joints using multi-directional polymer matrix composite laminates reinforced by high-modulus fibres by single-shear tensile loading of a two-piece specimen, according procedure B of the test standard ASTM D5961/D5961M [6]. Pull-through tests were performed according to ASTM D7332/D7332M standard, following procedure B [7]. This test procedure is used to determine the fastener pull-through resistance of multidirectional polymer matrix composites reinforced by high-modulus fibres.


a	b

Figure 3. Set-up for (a) Bearing strength test (single-shear configuration); (b) Pull-through resistance test.

These tests were conducted through a Universal Testing Machine Zwick Z100 equipped with a load cell up to 100 kN (Zwick Z100 BS1). The set-up for these tests is shown in the Figure 3. A face-mounted extensometer was used in the bearing tests.

2.2.3 Crippling tests

This test campaign covers the execution of quasi-static compression test on mono-stringers (skin + stringer), normally known as ‘crippling tests’. The crippling load is the ultimate load a stiffener loaded in uniaxial compression can undergo before final failure. This load can be experimentally determined if the stiffener is short enough, since long stiffeners often fail due to buckling before crippling load is reached.

An experimental procedure was developed for crippling test execution, including the design of the necessary tools to reproduce the representative boundary conditions. Seven specimens were extracted from the flat panel shown in the Figure 1 for execution of the crippling tests. Specimens’ length was 200 mm and specimen width was the total stringer width, 113 mm. In order to introduce compression load, aluminium end blocks were installed in the specimens. End blocks with different length were used, achieving specimen spans of 120 mm and 150 mm. Due to the specimen length, no lateral stabilization was required. The specimens were instrumented with strain gages.

Crippling tests were performed by means of a SCHENCK 2.5 MN Universal Testing Machine. The set-up for crippling test is shown in the Figure 4. First, a pre-test up to 15% of predicted failure load was executed. Then, the specimen was subjected to monotonic compression loading up to failure. The displacement rate was 0.5 mm/min. Data acquisition was performed using MGCPlus system, which allows high frequency data acquisition (100 Hz), real-time monitoring of the results (loads, displacements, strains), and synchronization of all the measurements.

Figure 4. Crippling test set-up.

In addition to traditional strain gauges, digital image correlation (ARAMIS system) was included to obtain the strain field in the central area of some of the specimens (skin surface). To this end, the specimen was white-painted and this surface was then prepared to monitor strain level. Likewise, laser displacement sensor with 8 µm accuracy was used to obtain actual displacement of the specimen, and avoid the error coming from the adjustments of the test machine in displacement recording. Additionally, High-Speed Camera was used to study failure mode of these specimens. Crack events were also recorded by means of a sound-level meter.

2.2.4 Unfolding and debonding tests

Test procedures were developed with the purpose of obtaining information on the unfolding and debonding failure modes and their admissible values for the structural detail formed by the frame-skin joint. The purpose was to obtain which were the primary and secondary failure modes depending on the loading introduced to the structure and to propose a design optimization for scaling-up to Level 3 specimen design.

Unfolding and debonding tests were performed by means of a Zwick Z100 Universal Test Machine, equipped with a load cell up to 100 kN. First, a pre-test was applied up to 15% of estimated failure load. After unloading, monotonic loading up to failure was applied. The displacement rate was 0.5 mm/min. All of the specimens were instrumented with strain gages. In order to assess intermediate cracks, sound-level meter was used in these tests.

Unfolding test set-up was modified according to the results obtained in the tests. The test set-up for unfolding specimens #1 and #2 is shown in the Figure 5. In first group of tests, a plate was used to clamp the skin-frame joint. The distance between frame radius and the clamping plate was reduced from specimen #1 to specimen #2.


a	b

Figure 5. Unfolding test set-up: (a) Specimen 1; (b) Specimen 2

The test set-up for the specimen #3 is shown in the Figure 6. In this test, fasteners were used to clamp the skin-frame joint.

Figure 6. Unfolding test – Specimen 3 - Set-up.

Clamping by means of a plate was proved to be a better solution to obtain unfolding as primary failure mode. Thus, specimen #4 was tested according to this configuration. In this case, distance between frame radius end and clamping plate was 12 mm.

In debonding tests, the set-up was similar for all the specimens. An example is shown in the Figure 7.

Figure 7. Debonding test set-up.

2.2.5 Mouse hole tests

The purpose of these tests is the characterization of the joint between the frame and the skin around the stringers, i.e. mouse hole area, when it is subjected to tensile loads. As a result, the admissible values of debonding or frame/stringer delamination failure mode are obtained.

Mouse hole tests were performed using a hydraulic actuator in a custom test rig equipped with a load cell of 250 kN. The displacement rate was 0.5 mm/min. Two different specimen configurations were tested. The first specimen was tested according test configuration 1, which includes metallic fittings (named as “clips”) reinforcing the joint between frame, stiffener and skin. In the Figure 8, the set-up for this mouse hole test is shown. Once this configuration was tested and structure behaviour including failure mode was valid, the second mouse hole was tested according test configuration 2, which does not include the clips. This allowed to evaluate structure behaviour and feasibility of the design without this reinforcement. Specimens were instrumented with strain gages to check proper strain distribution. In order to detect intermediate cracks, sound-level meter was applied in these tests as well.

Figure 8. Mouse hole specimen test set-up (configuration 1 – with clips).

3 Results

For all the FHT specimens, the failure occurred at the hole area. An example of this failure mode is shown in the Figure 9.

Figure 9. Example of FHT failure mode.

Images taken from the video-recording with High-Speed Camera of the fastener area during failure are shown in the Figure 10. The initiation and propagation of cracks around the fastener is observed.

Figure 10. Failure recorded from HSC (SPC 1).

In all of the OHC specimens, failure also passed through the hole. An example of this failure mode is shown in the Figure 11.

Figure 11. Example of OHC failure mode.

In bearing tests, for all of the specimens two failure mode were observed: laminate bearing at both holes as well as laminate pull-through at both holes in the laminate head side. An example is shown in the Figure 12. Additionally, one of the specimens exhibited fastener bending at the fastener head closer to the extensometer.

Figure 12. Example of bearing failure mode.

In pull-through tests, the failure mode was pull-through for all of the specimens. An example can be observed in the Figure 13.

Figure 13. Example of pull-through failure mode.

3.1 Crippling tests

Higher failure loads are observed for specimens CR-6 and CR-7. This is due to the greater thickness of these specimens, which were extracted from a section of panel area with extra thickness. From these results, it can be stated that influence of span is not significant for this test specimen geometry.The Figure 14 shows an example of the crippling specimens after failure and its corresponding image taken from the High-Speed camera recording. Explosive failure mode is observed for all of the specimens.

Figure 14. Failure mode of crippling specimen #7 and its image from High-Speed Camera recording.

Figure 15 shows the evolution of the strain level in the specimen CR-4, measured through Digital Image Correlation, at (a) 0% load; (b) 25% load; (c) 50% load; (d) 75% load; (e) 100% load. It is observed a uniform deformation of the skin side of the specimen.

a

b

c

d

e

Figure 15 . Evolution of the strain level in the specimen CR-4, measured through Digital Image Correlation, at (a) 0%; (b) 25%; (c) 50%; (d) 75%; (e) 100% of failure load.

An example of load curve correlated with the signal from sound-level meter is shown in the Figure 16. It can be observed that sound peaks match with small load drops before failure, which correspond to intermediate cracks in the specimen throughout the test.

Figure 16. Load and sound curves of the specimen CR-4.

3.2 Unfolding and debonding tests

As commented before, this test presents the particular challenge in design of different boundary conditions in such way that the first failure of the specimens is provoked, on one hand, by a debonding between skin and stiffener and, on the other hand, by a delamination of the unfolded plies in the stiffener radius area.

For unfolding specimens #1 and #2, debonding took place before failure of the radius occurred. Thus, a modification of the boundary conditions was necessary to obtain information on the desired unfolding failure mode.

Figure 17. Failure mode of the first unfolding specimen. Similar failure was found in the specimen #2.

For this purpose, fastener clamping was proposed for the following test. This configuration resulted in a significant skin flexure took place during the test, leading to skin delamination before the final unfolding failure. The specimen after failure is shown in the Figure 18.

Figure 18. (a) Skin bending and delamination before unfolding failure mode (b) of the third specimen.

The failure mode of the fourth unfolding specimen was similar to the failure of specimens #1 and #2: debonding of the skin-frame joint took place before final unfolding failure.

Debonding specimen failure mode was the same for all the specimens.

As it is shown in the Figure 19, the frame was debonded from the skin. Figure 20 shows an example of the progression of the debonding along with the load-displacement curve.

Figure 19 . Failure mode of the first debonding specimen.

Figure 20 . Load-displacement curve of debonding test (specimen 2).

As a result of this campaign, a set of failure loads was obtained for the different failure modes along with useful information for the structural joint design solution that is to be applied on the thermoplastic fuselage panel design.

3.3 Mouse hole tests

The Figure 21 shows the first mouse hole specimen after failure. The failure load was 28.1 kN. As it can be observed, clip-stringer bolted joint failed. Debonding of skin-frame joint was also noticed.No damage was observed in the lateral edges of the specimen after failure (Figure 22).

Figure 22. Lateral edges of the mouse hole specimen 1 after failure.

Figure 23 shows the second mouse hole specimen after failure. The failure load was 3.15 kN. As it can be observed, the specimen failed due to frame-skin joint debonding.

Figure 23. Mouse hole specimen 2 after failure.

4 Conclusions

The mechanical behaviour of the thermoplastic material has been assessed, and the allowables have been obtained for the design of the curved thermoplastic fuselage panel.

Standardized test results showed a low level of dispersion, which reflects a suitable manufacturing process. Regarding element tests, it was found that debonding of skin-frame is a critical failure mode that should be controlled in the design of the sub-component tests. This behaviour is highlighted in mouse hole tests, where better results were obtained with the specimen reinforced by the clips. This solution will be finally adopted by the manufacturer, who will include the clips in the frames of the curved panel.

The advanced monitoring techniques, such as Digital Image Correlation, High-Speed Camera and sound-level meter, have been successfully applied. These techniques provided useful information about the deformation and failure mode of the specimens throughout the tests, which could not have been obtained with standard test instrumentation.

The execution of this test campaign has allowed to obtain valuable information about the mechanical behaviour of the fuselage panel components. This knowledge will be applied in the final design of the curved thermoplastic panel. Future validation of this aerostructure as part of DELTA will finally have a positive environmental impact. Due to its re-usability and recyclability advantages, usage of thermoplastic resin based carbon fibre polymers will mainly contribute to the reduction of Greenhouse Gas (GHG) emissions.

The research leading to these results has gratefully received funding from the European JTI- CleanSky2 program under the Grant Agreement nº 831862 (DELTA). This project is coordinated by Element Seville, and lead by AERNNOVA, as Topic Manager. Likewise, the authors wish to thank the collaboration with FIDAMC, as manufacturer of panel specimen.

References

[1] Oguzhan Bas, Elvan Ates, Fahrettin Ozturk. Thermoplastic Composite Materials for the Aerospace Industry. Res Dev Material Sci. 15(5). RDMS.000872. 2021. DOI: 10.31031/RDMS.2021.15.000872

[2] https://www.project-delta.es/

[3] ASTM Standard D5766/D5766M – 11, “Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates”, ASTM International, July 2018, DOI: 10.1520/D5766_D5766M-11R18.

[4] ASTM Standard D6742/D6742M – 17, “Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates”, ASTM International, October 2017, DOI: 10.1520/D6742_D6742M-17

[5] ASTM Standard D6484/D6484M – 14, “Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates”, ASTM International, 2014

[6] ASTM Standard D5961/D5961M – 17, “Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates”, ASTM International, September 2017, DOI: 10.1520/D5961_D5961M-17.

[7] ASTM Standard D7332/D7332M – 16, “Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite”, ASTM International, August 2016, DOI: 10.1520/D7332_D7332M-16

@@ Line 255: / Line 255: @@
 ==3 Results==
-<span id='_Ref65242298'></span><span id='_Toc84594988'></span>A summary of the results for the standardized tests is shown in the <span id='cite-_Ref100071555'></span>[[#_Ref100071555|Table 2]].
+<span id='_Ref65242298'></span><span id='_Toc84594988'></span><span id='cite-_Ref100071555'></span>For all the FHT specimens, the failure occurred at the hole area. An example of this failure mode is shown in the <span id="cite-_Ref65242299"></span>[[#_Ref65242299|Figure 9]].
-<div id="_Ref100071555" class="center" style="width: auto; margin-left: auto; margin-right: auto;">
-<span style="text-align: center; font-size: 75%;">'''Table ''' '''2''' '''. '''Results for standardized tests.</span></div>
-{| style="width: 100%;margin: 1em auto 0.1em auto;border-collapse: collapse;"
-|-
-|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;vertical-align: top;"|
-|  style="border-left: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Average'''</span>
-|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''VC (%)'''</span>
-|-
-|  style="border-right: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Filled-hole tensile strength (MPa)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">521</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2</span>
-|-
-|  style="border-right: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Open-hole compressive strength (MPa)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">286</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">2</span>
-|-
-|  style="border-right: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Ultimate bearing stress (MPa)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">803</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">3</span>
-|-
-|  style="border-right: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Bearing chord modulus (GPa)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">9.57</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">8</span>
-|-
-|  style="border-right: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Offset bearing strength (MPa)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">652</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">5</span>
-|-
-|  style="border-right: 1pt solid black;"|<span style="text-align: center; font-size: 75%;">'''Pull-through ultimate load (kN)'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">12.1</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">3</span>
-|}
-For all the FHT specimens, the failure occurred at the hole area. An example of this failure mode is shown in the <span id='cite-_Ref65242299'></span>[[#_Ref65242299|Figure 9]].
 [[Image:Draft_Sanchez_378758303-image17-c.png|600px]]
@@ Line 357: / Line 320: @@
 ==='''3.1''' Crippling tests===
-A summary of results on crippling tests is covered in the <span id='cite-_Ref63853781'></span>[[#_Ref63853781|Table 3]]. Higher failure loads are observed for specimens CR-6 and CR-7. This is due to the greater thickness of these specimens, which were extracted from a section of panel area with extra thickness. From these results, it can be stated that influence of span is not significant for this test specimen geometry.
+<span id='cite-_Ref63853781'></span>Higher failure loads are observed for specimens CR-6 and CR-7. This is due to the greater thickness of these specimens, which were extracted from a section of panel area with extra thickness. From these results, it can be stated that influence of span is not significant for this test specimen geometry.<span id="_Ref63853781"></span><span id="_Toc65153950"></span>The <span id='cite-_Ref65057415'></span>[[#_Ref65057415|Figure 14]] shows an example of the crippling specimens after failure and its corresponding image taken from the High-Speed camera recording. Explosive failure mode is observed for all of the specimens.
-<span id='_Ref63853781'></span><span id='_Toc65153950'></span><div id="_Toc84595003" class="center" style="width: auto; margin-left: auto; margin-right: auto;">
-<span style="text-align: center; font-size: 75%;">'''Table 3.''' Crippling test results.</span></div>
-{| style="width: 100%;margin: 1em auto 0.1em auto;border-collapse: collapse;"
-|-
-|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;vertical-align: top;"|
-|  style="border-left: 1pt solid black;border-bottom: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''Free length (mm)'''</span>
-|  style="border-bottom: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''Failure load (kN)'''</span>
-|-
-|  style="border-top: 1pt solid black;border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-1'''</span>
-|  style="border-top: 1pt solid black;border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">120</span>
-|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">365</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-2'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">120</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">351</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-3'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">150</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">354</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-4'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">120</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">387</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-5'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">120</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">376</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-6'''</span>
-|  style="border-left: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">150</span>
-|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">460</span>
-|-
-|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''497-DELTA-CR-7'''</span>
-|  style="border-left: 1pt solid black;border-bottom: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">150</span>
-|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">465</span>
-|}
-The <span id='cite-_Ref65057415'></span>[[#_Ref65057415|Figure 14]] shows an example of the crippling specimens after failure and its corresponding image taken from the High-Speed camera recording. Explosive failure mode is observed for all of the specimens.
 {| style="width: 71%;margin: 1em auto 0.1em auto;border-collapse: collapse;"
@@ Line 449: / Line 371: @@
 ==='''3.2''' Unfolding and debonding tests===
-<span id='cite-_Ref75517761'></span>[[#_Ref75517761|Table 4]] summarizes the maximum load achieved in unfolding and debonding tests.
+<span id='cite-_Ref75517761'></span><span id="_Ref75517761"></span>As commented before, this test presents the particular challenge in design of different boundary conditions in such way that the first failure of the specimens is provoked, on one hand, by a debonding between skin and stiffener and, on the other hand, by a delamination of the unfolded plies in the stiffener radius area.
-<span id='_Ref75517761'></span><div id="_Toc84595010" class="center" style="width: auto; margin-left: auto; margin-right: auto;">
-<span style="text-align: center; font-size: 75%;">'''Table ''' '''4''' '''. '''Unfolding and debonding test results.</span></div>
-{| style="width: 67%;margin: 1em auto 0.1em auto;border-collapse: collapse;"
-|-
-|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;"|
-|  style="border-bottom: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">'''Maximum load (kN)'''</span>
-|-
-|  style="border-top: 1pt solid black;border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-UNF-1</span>
-|  style="border-top: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">8.38</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-UNF-2</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">9.31</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-UNF-3</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">7.25</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-UNF-4</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">7.66</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-DEB-1</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">1.33</span>
-|-
-|  style="border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-DEB-2</span>
-|  style="text-align: center;"|<span style="text-align: center; font-size: 75%;">1.09</span>
-|-
-|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">497-DELTA-DEB-3</span>
-|  style="border-bottom: 1pt solid black;text-align: center;"|<span style="text-align: center; font-size: 75%;">1.11</span>
-|}
-As commented before, this test presents the particular challenge in design of different boundary conditions in such way that the first failure of the specimens is provoked, on one hand, by a debonding between skin and stiffener and, on the other hand, by a delamination of the unfolded plies in the stiffener radius area.
 For unfolding specimens #1 and #2, debonding took place before failure of the radius occurred. Thus, a modification of the boundary conditions was necessary to obtain information on the desired unfolding failure mode.
@@ Line 526: / Line 415: @@
 ==='''3.3''' Mouse hole tests===
-The <span id='cite-_Ref65145648'></span>[[#_Ref65145648|Figure 21]] shows the first mouse hole specimen after failure. The failure load was 28.1 kN. As it can be observed, clip-stringer bolted joint failed. Debonding of skin-frame joint was also noticed.
+The <span id='cite-_Ref65145648'></span>[[#_Ref65145648|Figure 21]] shows the first mouse hole specimen after failure. The failure load was 28.1 kN. As it can be observed, clip-stringer bolted joint failed. Debonding of skin-frame joint was also noticed.<span id="_Ref65145648"></span><span id="_Toc65154113"></span>No damage was observed in the lateral edges of the specimen after failure (<span id='cite-_Ref65146159'></span>[[#_Ref65146159|Figure 22]]).
-<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
-''' [[Image:Draft_Sanchez_378758303-image42-c.png|420px]] '''</div>
-<span id='_Ref65145648'></span><span id='_Toc65154113'></span><div id="_Toc84595168" class="center" style="width: auto; margin-left: auto; margin-right: auto;">
-<span style="text-align: center; font-size: 75%;">'''Figure 21.''' Mouse hole specimen 1 after failure. </span></div>
-No damage was observed in the lateral edges of the specimen after failure (<span id='cite-_Ref65146159'></span>[[#_Ref65146159|Figure 22]]).
 <div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
@@ Line 580: / Line 461: @@
 <div id="6"></div>
-[[#cite-6|[6]]] ASTM Standard D5961/D5961M – 17, “Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates”, ASTM International, September '''2017''', DOI: 10.1520/D5961_D5961M-17.
+[[#cite-6|[6]]] ASTM Standard D5961/D5961M – 17, “Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates”, ASTM International, September '''2017''', DOI: 10.1520/D5961_D5961M-17.<span id="_GoBack"></span><div id="7"></div>
-<span id='_GoBack'></span><div id="7"></div>
 [[#cite-7|[7]]] ASTM Standard D7332/D7332M – 16, “Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite”, ASTM International, August '''2016''', DOI: 10.1520/D7332_D7332M-16