Abstract

Rib or grid stiffened structures have been investigated for decades, mainly for application in space structures. Grid structures offer the possibility to develop more damage tolerant structures as the network of ribs can provide redundant load paths. In an ideal situation, an aircraft fuselage could have a load carrying grid with ribs that carry tensile, compressive and shear loads. The skin would only need to sustain the cabin pressure load. Such a configuration could lead to significant weight reduction as a different design philosophy can be used. Typically, a damage tolerant design approach allowing a maximum of 3000 µstrain is used for composite aircraft structures. Using a grid structure, a different approach could be developed for a design which could allow strains up to 6000 µstrain. Automated fibre placement has made composite grid structures an affordable option. However, they pose a major challenge in the development of tooling for cure due to their complex and sometimes irregular structure. Within the European funded Horizon 2020 ACASIAS programme, square antenna elements are developed to be integrated in a composite aircraft fuselage panel. For this reason, an orthogrid stiffener pattern was chosen. As the skin of the panel must be transparent for the antenna signals, a glass fibre skin is required. A glass fibre skin to carry shear loads and carbon fibre ribs to carry compression and tension loads is therefore being developed to be able to meet structural and electromagnetic requirements. This paper describes aspects of the ongoing development for the design, manufacture and testing of an orthogrid stiffened structure in an efficient way. Simple alternating cutting of tapes at the crossing appear to be a suitable solution with a tensile stiffness reduction of 10 % compared to the situation without cuts. These and other details and elements are tested to validate the final design. The use of reusable silicone vacuum bags was investigated in order to replace complex metal tooling blocks. Besides saving on mould materials and machining, the use of a preshaped silicone vacuum bag is expected to reduce labour cost due to a decrease in handling of tooling blocks for positioning and cleaning. The first trial indicates that good quality laminates can be obtained using reusable vacuum bags. More testing will be carried out to validate the concept for a large 3×1.2 m panel.

Full document

The PDF file did not load properly or your web browser does not support viewing PDF files. Download directly to your device: Download PDF document

References

[1] H. Schippers et al., “Broadband Conformal Phased Array with Optical Beam Forming for Airborne Satellite Communication”, IEEE Aerospace Conf., March 2008, Big Sky, MT, USA.

[2] S. Panthi, J. King, and C. McLain. "The eXConnect Broadband Aeronautical Service", 31st AIAA International Communications Satellite Systems Conference (ICSSC), (AIAA 2013-5621), October 14-17, 2013, Florence, Italy. https://doi.org/10.2514/6.2013-5621

[3] ACASIAS web site at http://www.acasias-project.eu/objectives-and-innovations-11, Accessed 21 March 2019.

[4] Steven M. Huybrechts, Steven E. Hahn and Troy E. Meink, “Fabrication, analysis and design methods”, ICCM12 Conference, Paris, July 1999, paper 357 , ISBN 2-9514526-2-4

[5] J. M. Müller and W. van den Brink, “Comparison of integrated rib stiffened and L-blade stiffened composite panels manufactured using simple tooling methods,” in SAMPE Technical Conference, Long Beach, USA, 2016.

[6] Michael P. Kleiman, “Light carbon-fiber structure protects heavy space cargo”, AFRL Space Vehicles Directorate, February 26, 2007. Available at: https://www.wpafb.af.mil/News/Article-Display/Article/401406/light-carbon-fiber-structure-protects-heavy-space-cargo/ Accessed 21 March 2019.

Back to Top
GET PDF

Document information

Published on 15/02/21
Accepted on 03/03/21
Submitted on 03/03/21

DOI: 10.23967/emus.2019.018
Licence: CC BY-NC-SA license

Document Score

0

Views 21
Recommendations 0

Share this document

claim authorship

Are you one of the authors of this document?