Lansink-Rotgerink et al 2020a - Revision history

Scipediacontent at 07:35, 16 February 2021

2021-02-16T07:35:37Z

Scipediacontent at 08:49, 11 February 2021

2021-02-11T08:49:12Z

Scipediacontent: Scipediacontent moved page Draft Content 249663902 to Lansink-Rotgerink et al 2020a

2021-02-11T08:46:37Z

Scipediacontent moved page Draft Content 249663902 to Lansink-Rotgerink et al 2020a

Scipediacontent: Created page with " == Abstract == Replacement of protruding antennas by integrated alternatives will reduce the energy consumption and NOx and CO2 emissions of an aircraft. This paper proposes..."

2021-02-11T08:46:05Z

Created page with " == Abstract == Replacement of protruding antennas by integrated alternatives will reduce the energy consumption and NOx and CO2 emissions of an aircraft. This paper proposes..."

New page

== Abstract ==

Replacement of protruding antennas by integrated alternatives will reduce the energy consumption and NOx and CO2 emissions of an aircraft. This paper proposes and integrated VHF cavity backed slot antenna that is suitable to replace blade antennas. To reduce the size of the cavity a parallel plate resonator is used. The slot is integrated into a fibre metal laminate fuselage panel. A bookleafing principle is used to reinforce the panel at the position of the slot, making sure the material quality is not reduced. Measurement results of a demonstrator antenna show the feasibility of the proposed antenna. Moreover, the paper discusses several electromagnetic and structural design trade-offs for this integrated antenna.

== Full document ==
<pdf>Media:Draft_Content_249663902-P_IDC5_30-6716-document.pdf</pdf>

== References ==

[1] D. Sievenpiper, L. Zhang, R.F. Jimenez Broas, N.G. Alexópolous, E. Yablonovitch, “High-impedance electromagnetic surfaces with a forbidden frequency band”, ''IEEE Trans. on Antennas and Prop''. (1999), '''47''' (11): 2059-2074.

[2] J. Joubert, J.C. Vardaxoglou, W.G. Whittow and J.W. Odendaal, “CPW-fed cavity-backed slot radiator loaded with an AMC reflector”,'' IEEE Trans. on Antennas and Prop''. (2012), '''60''' (2): 735-742.

[3] H. Malekpoor and S. Jam, “Improved radiation performance of low profile printed slot antenna using wideband planar AMC surface”, ''IEEE Trans. on Antennas and Prop.'' (2016), '''64''' (11): 4626-4638.

[4] J. Li, H. Shi and A. Zhang, “Unidirectional circularly polarized slot antenna backed with miniaturized AMC reflector''”, IEEE Int. Symp. on Antennas and Prop. & USNC/URSINat. Radio Sc. Meeting, Boston'', MA, USA, July 2018.

[5] W. Hong and K. Sarabandi, “Platform embedded slot antenna backed by shielded parallel plate resonator”, ''IEEE Trans. on Antennas and Prop''. (2010), '''58''' (9): 2850-2857.

[6] N. Behdad and K. Sarabandi, “A wide-band slot antenna design employing a fictitious short circuit concept”, ''IEEE Trans. on Antennas and Prop''. (2005), '''53''' (1): 475-482.

@@ Line 2: / Line 2: @@
 == Abstract ==
-Replacement of protruding antennas by integrated alternatives will reduce the energy consumption and <math>NO_x</math> and <math>CO_2</math> emissions of an aircraft. This paper proposes and integrated VHF cavity backed slot antenna that is suitable to replace blade antennas. To reduce the size of the cavity a parallel plate resonator is used. The slot is integrated into a fibre metal laminate fuselage panel. A bookleafing principle is used to reinforce the panel at the position of the slot, making sure the material quality is not reduced. Measurement results of a demonstrator antenna show the feasibility of the proposed antenna. Moreover, the paper discusses several electromagnetic and structural design trade-offs for this integrated antenna.
+Replacement of protruding antennas by integrated alternatives will reduce the energy consumption and NO<sub>x</sub> and CO<sub>2</sub> emissions of an aircraft. This paper proposes and integrated VHF cavity backed slot antenna that is suitable to replace blade antennas. To reduce the size of the cavity a parallel plate resonator is used. The slot is integrated into a fibre metal laminate fuselage panel. A bookleafing principle is used to reinforce the panel at the position of the slot, making sure the material quality is not reduced. Measurement results of a demonstrator antenna show the feasibility of the proposed antenna. Moreover, the paper discusses several electromagnetic and structural design trade-offs for this integrated antenna.
 == Full document ==

← Older revision	Revision as of 08:46, 11 February 2021
(No difference)